Jinzhou Shuangxing Railway Equipment Factory

Internal combustion rail sawing machine. Industry standard
--Jinzhou Shuangxing# Twenty years of professional manufacturing
Contact person: Ms. Fu
Address: Songpo, Linghe District, Jinzhou City, Liaoning Province Road
Fax -
Customer consultation
--Strive to create the leading brand in the industry # Jinzhou Shuangxing
Internal combustion rail saw machine._Picture_Price_Production
Jinzhou Shuangxing Railway Machinery Co., Ltd. is located in the southwest of Liaoning Province, bordering the Songling Mountains to the north and the Bohai Sea to the south and Liaodong Bay. It is located at the eastern end of the famous Western Liaoning Corridor, a transportation hub connecting Northeast China and North China. Beijing-Harbin Railway, Qin-Shenyang Railway Passenger Dedicated Line, Dazheng Railway, Jincheng Railway, Gouhai Railway, Beijing-Harbin Highway, Beijing-Shenyang Expressway, and Liaoning Binhai Highway traverse the entire territory. Jinfu Expressway, Jinchao Expressway and national highway. It forms a one-hour economic circle with Huludao, Panjin, Chaoyang and Fuxin.
Internal combustion rail sawing machine._Picture_Price_Production
Internal combustion rail sawing machine is an ideal rail cutting tool for railway engineering, bridge, line overhaul and other departments. It is suitable for maintenance and emergency repair of railway laying lines. , Especially the rail cutting operation in areas and sections without power supply can also be applied to rails of various specifications and is especially suitable for heavy rails above.
.Technical parameters of internal combustion rail sawing machine
.Rail cutting range:-steel rail
.Power: .horsepower
.Grinding wheel utilization rate:
Rail-sub-rail- Secondary
Rail-Second rail-Second
The rail cutting time is not greater than the verticality. Parallelism
. Roughness: above
. Overall dimensions:
. Whole machine weight:
.Grinding wheel size:
Internal combustion rail saw machine._Picture_Price_Production
Instructions for use
First install the thin grinding wheel and check the thin grinding wheel before installing the grinding wheel. Whether there are cracks, moisture deformation, and whether both sides are flat. Uneven surfaces may cause the incision to deviate and the clamp to be tightened. After installing the disc, tighten the locking nut, but the torque should not be too large to avoid crushing the thin grinding wheel.
Install the rail cutting machine on the rail and pull out the positioning rod installed on the fixture. At this time, the position indicated by the end surface of the positioning rod is the cutting position of the grinding wheel. Move the rail cutting machine to the preset cutting position as needed. Then make the inner surface (convex surface) of the fixture closely contact the top surface of the rail and the lower part of the rail palate and tighten the set bolts. The rail cutting machine is in working condition.
. Pull the joystick with one hand to keep the rail cutting machine above the rail, while holding the other joystick with the other hand to prevent the sheet grinding wheel from hitting the rail.
After installing the rail cutting machine, pull the starting handle to start the internal combustion engine. After the internal combustion engine is started, run at idle speed for no less than 2 seconds to check whether all parts of the machine are normal. If there are any abnormalities, shut down to eliminate them. Increase the throttle and observe whether the thin disc grinding wheel is running smoothly, whether it is deflected, and whether all parts are running normally. If any abnormality is found, the machine should be stopped to replace the grinding wheel or troubleshoot. Before cutting, adjust the throttle and damper to meet cutting needs.
When cutting, the feeding of the thin grinding wheel mainly depends on the dead weight of the rail cutting machine and the swing of the joystick. Therefore, when holding the joystick with both hands, do not exert downward force and swing the joystick rhythmically as needed.
During the cutting process, the joystick should be kept swinging back and forth and should not stop somewhere. When pinching occurs, slowly lift the lamella grinding wheel and continue cutting. If pinching still occurs, stop the machine to check the cause or replace the lamella grinding wheel. When re-cutting, the thin grinding wheel must perfectly match the original incision, otherwise the cutting position should be changed.
If the cut is tilted during the cutting process, the machine should be stopped to check the cause, eliminate the fault, or replace the thin grinding wheel, change the cutting position, and start cutting again.
Usually, the top of the rail is cut first, then the waist, and then the bottom until it is cut off.
When the thin grinding wheel is worn to a certain extent (the diameter of the grinding wheel is approximately less than 10 mm), it may not be possible to cut the rail from one side of the rail. At this time, the grinding wheel needs to be moved to the other side to cut the rail in half until it is cut. When the diameter of the grinding wheel is less than about 100% due to the reduction in linear speed of the grinding wheel, the wear of the grinding wheel will be accelerated. At this time, even if the rail is cut in half, it may not be completely cut off. It is recommended to replace the thin grinding wheel to avoid replacing the grinding wheel without cutting the rail, causing the new grinding wheel to not match the original cut.
Internal combustion rail saw machine._Picture_Price_Production
Jinzhou Shuangxing after-sales service commitment:
Service tenet: fast, decisive, accurate, thoughtful and thorough.
, Service goal: Service quality wins user satisfaction.
Service efficiency: If the equipment fails during or outside the warranty period, the supplier's maintenance personnel can arrive at the site and start repairs within hours after receiving notification.
Service principle: The product warranty period is one to twelve months. During the warranty period, the supplier will repair and replace parts that are damaged due to quality reasons for free. Parts that are damaged outside the warranty period will only be provided at cost. Equipment damage caused by human factors on the part of the buyer shall be repaired or accessories provided by the supplier at cost price.
Jinzhou Shuangxing produces and sells the following products
☆Railway transportation: internal combustion tamping picks, tamping machines, hydraulic rail drilling machines, hydraulic rail drilling machines, manual rail drilling machines, rack type Track starter, hydraulic track starter, rail cutting machine, square sleeper, hydraulic rail straightener, rerailer, universal gauge ruler, rail grinder, square ruler, rail transport car, etc.
☆Track accessories: stoppers Plate, turnout, turnout accessories, turnout tie rod, track gauge ruler, track gauge ruler, track gauge ruler, track gauge ruler, anchor rod, anchor drill rod, pneumatic drill rod, turnout pad, track plywood, road stud, insulating plywood, Crossover switches, pads, composite rubber pads, track fasteners, track clamps, gauge pull rods, rail guard gussets, line gusset bases, insulated gauge rods, gussets, twist drill pipes, coal drill pipes, twist drills Rod, connecting sleeve, chain spreader, wind drill, anchor pallet, pallet, nylon baffle seat, manual switch, manual bender, bender, bending machine, rail pressure plate, fish tail plates, fishtail bolts, etc.
Jinzhou Shuangxing sales network Hebei, Shanxi, Inner Mongolia, Liaoning, Jilin, Heilongjiang, Beijing, Tianjin, Shanghai, Jiangsu, Zhejiang, Anhui, Fujian, Jiangxi, Shandong, Henan, Hubei, Chongqing, Sichuan, Guizhou, Yunnan, Shaanxi, Gansu, Ningxia, Xinjiang and other places.
Remarks: The above content has related product parameters and pictures provided by Jinzhou Shuangxing Railway Machinery Co., Ltd. for reference only. Specific products may have different sources due to different production batches. Please contact the sales staff for specific details.